| View previous topic :: View next topic |
| Author |
Message |
Midwinter
Joined: 13 Apr 2011
Posts: 41
|
 Posted: Wed Dec 14, 2011 10:34 pm Post subject: Servo Drive Belt Issue or Arm Drive Belt Issue? |
 |
|
I just fired up a CED player I received with a 100 disc collection (it is either the SFT100, SGT100, or the SGT101 - how would I know which one? - The one I have has woodgrain)
It plays a minute or so of video and then it skips back to an earlier section of video and plays the same 4 frames or so again and again. You can even fast forward the video to a few minutes or more in and it will sometimes skip back to the 4 frame sequence all the way back at the beginning of the disc.
Any help identifying the problem would be appreciated!
_________________
My SJT400 keeps me warm MIDWINTER when the OSD board overheats!
Trying my wife's patience one purchase at a time. |
|
| Back to top |
|
 |
Rixrex
Joined: 28 May 2004
Posts: 1222
|
|
| Back to top |
|
|
Midwinter
Joined: 13 Apr 2011
Posts: 41
|
| Posted: Thu Dec 15, 2011 9:08 am Post subject: |
|
|
I read the guide and that is how I narrowed it down to either of those two belts. I don't have a player that has page mode so I'm not exactly sure what that looks like. If I posted a video of what is going on would that help someon determine which belt is at fault?
_________________
My SJT400 keeps me warm MIDWINTER when the OSD board overheats!
Trying my wife's patience one purchase at a time. |
|
| Back to top |
|
|
Rixrex
Joined: 28 May 2004
Posts: 1222
|
| Posted: Thu Dec 15, 2011 6:32 pm Post subject: |
|
|
Well, that player has only two belts:
1. Servo Drive Velt
2. Turntable Drive Belt
The Servo belt does duty as the stylus arm drive belt via a series of gears and a clutch. So best to replce that Servo belt, I'd say, and maybe buy the turntable belt at the same time to have it available. |
|
| Back to top |
|
|
Midwinter
Joined: 13 Apr 2011
Posts: 41
|
| Posted: Thu Dec 15, 2011 7:43 pm Post subject: |
|
|
I appreciate your help!
_________________
My SJT400 keeps me warm MIDWINTER when the OSD board overheats!
Trying my wife's patience one purchase at a time. |
|
| Back to top |
|
|
rein-o
Joined: 05 Apr 2012
Posts: 34
Location: nashville TN
|
| Posted: Tue Apr 10, 2012 8:30 pm Post subject: |
|
|
| my servo belt looks fine but it does the same thing, is it best to just replace? |
|
| Back to top |
|
|
Rixrex
Joined: 28 May 2004
Posts: 1222
|
| Posted: Tue Apr 10, 2012 8:47 pm Post subject: |
|
|
| Yeah, it can look good but still be slipping. |
|
| Back to top |
|
|
rein-o
Joined: 05 Apr 2012
Posts: 34
Location: nashville TN
|
| Posted: Tue Apr 10, 2012 9:30 pm Post subject: |
|
|
sounds good, picture quality looks O.K. so the stylus is fine.
i'll order some belts and off i go!!
after fixing arcade machines and some pinballs these aren't that bad.
but it's not that easy, like i tell my girlfriend, it's common sense!!  |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
