View previous topic :: View next topic |
Author |
Message |
kilgen
Joined: 11 Feb 2016 Posts: 3
|
Posted: Thu Feb 11, 2016 7:21 pm Post subject: SKT-090 Repair |
|
|
Hello;
I have an SKT-090 player that was given to me many years ago. I decided I would like to restore it to working condition.
I do know that the load belt melted and I think a resistor associated with the load motor circuit burned out.
I plan to open up the unit and see if I can replace the load belt and the burned out parts but it is unlikely I will be able to ascertain the resistor values if the part is burned.
Can someone on this forum point me in the right direction.
Gary W9TOF |
|
Back to top |
|
|
SelectaVision420
Joined: 25 Mar 2012 Posts: 1424 Location: Hartford
|
Posted: Thu Feb 11, 2016 8:29 pm Post subject: |
|
|
this topic is a few posts down. the skt090 is mutually the same chassis as the sjt line of players.
http://www.cedmagic.com/forum/viewtopic.php?t=2568 _________________ (2)Sears 274 & 934(80150,10&11350), sft100, sgt250, sjt 090-400, vp550, VDR3000, VP2000 & 4000
complete '84 Dimensia Owner |
|
Back to top |
|
|
kilgen
Joined: 11 Feb 2016 Posts: 3
|
Posted: Thu Feb 11, 2016 8:37 pm Post subject: |
|
|
And I thank you. I downloaded the PDF service manual. Hopefully I can get this machine working again. I plan to une it with my 1965 Zenith TV. Gary |
|
Back to top |
|
|
Daxi Don
Joined: 24 Dec 2006 Posts: 75 Location: Indiana
|
Posted: Wed Mar 02, 2016 10:55 am Post subject: SKT 090 Repair |
|
|
Did you find the repair info in the service data ? The resistor that may have opened is R5917 22 ohm. But before you remove the circuit board check the following. Measure the voltage on the function motor when the caddy is loading. The voltage should be approx. 15 VDC. If OK then the driver cct and R5917 are good. The function motor may be bad. |
|
Back to top |
|
|
kilgen
Joined: 11 Feb 2016 Posts: 3
|
Posted: Wed Mar 02, 2016 11:48 am Post subject: Re: SKT 090 Repair |
|
|
Daxi Don wrote: | Did you find the repair info in the service data ? The resistor that may have opened is R5917 22 ohm. But before you remove the circuit board check the following. Measure the voltage on the function motor when the caddy is loading. The voltage should be approx. 15 VDC. If OK then the driver cct and R5917 are good. The function motor may be bad. |
Hi. Yes I did get the service PDF and R5917 is definitely open. I am waiting for parts. I have probably over 2000 resistors in my shop but not one 22 ohm resistor was to be found. I have been posting a youtube video on the project. My youtube ID is HD7100.
Thanks! Gary |
|
Back to top |
|
|
Daxi Don
Joined: 24 Dec 2006 Posts: 75 Location: Indiana
|
Posted: Wed Mar 02, 2016 12:27 pm Post subject: SKT090 R5917 |
|
|
Gary,
CEDatum stocks this part R5917 22 ohm. RCA Part number 163285.
E-mail: cedatum@ccrtc.com |
|
Back to top |
|
|
SelectaVision420
Joined: 25 Mar 2012 Posts: 1424 Location: Hartford
|
Posted: Wed Mar 02, 2016 6:53 pm Post subject: |
|
|
glad to hear you were able to figure it out! i subscribed to you on youtube, my channel is "Tony Fleetwood" _________________ (2)Sears 274 & 934(80150,10&11350), sft100, sgt250, sjt 090-400, vp550, VDR3000, VP2000 & 4000
complete '84 Dimensia Owner |
|
Back to top |
|
|
|